*should not be run more than 15minutes continuous in a non-metal light to prevent module damage/over-heating

The M60 is a simple drop-in upgrade which replaces the standard incandescent bulb with a brighter, more efficient, shock proof, long-life (50,000 hours) LED assembly.

This is the Malkoff Devices P60 style drop-in with solid brass heat sink construction. This design utilizes a Cree 8 degree optic. The optic has a very nice balance between throw and spill. It is an outstanding room lighter and short to medium spotter. It was designed specifically for use in SureFire 6P, 6Z, C2, M2 and G2 flashlights. It may or may not fit other models. The input voltage is 3.8 - 9 volts. Below 3.8 volts it will drop out of regulation and run direct drive. The output is 235+ lumens. The current draw is only 750ma at 6 volts. The runtime is 1 1/2+ hours on 2 CR123 primary batteries. It will easily illuminate objects at 350+ feet and will blind opponents within a 100 foot radius. The LED is a Cree XRE 7090.

A fitting ring is required if used with a shock-absorbing head (ie M2).

Note: This mod will not work in Wolf Eyes Lights.

WARNING: This light is capable of causing eye damage at close range. Please use the light responsibly!!!
Module is not protected against reverse polarity. Do not exceed the maximum voltage of 9volts.
Note: This drop-in module was intended to operate at maximum brightness for tactical usage similar to the original setup. Operating the unit for more than 15 continuous minutes in plastic lights may cause damage to the drop-in module. This is not an issue in metal lights.

M60F 20 Degree Flood

This is the Malkoff Devices P60 style flood beam dropin with solid brass heatsink construction. This design utilizes a Cree 20 degree optic. The optic produces an outstanding room lighting beam. Throw is typically limited to approximately 120+/- feet. It will easily blind opponents at close range. It was designed specifically for use in SureFire 6P, 6Z, C2, M2 and G2 flashlights. It may or may not fit other models. The input voltage is 3.8 - 9 volts. Below 3.8 volts it will drop out of regulation and run direct drive. The output is 220+ lumens. The current draw is only 750ma at 6 volts. The runtime is 1 1/2+ hours on 2 CR123 primary batteries. The LED is a Cree XRE 7090

$53.99

M60LF (low output, flood)

This is the Malkoff Devices P60 style flood beam dropin with solid brass heatsink construction. This design utilizes a Cree 20 degree optic. The optic produces an outstanding room lighting beam. Throw is typically limited to approximately 80+/- feet. It will easily blind opponents at close range. It was designed specifically for use in SureFire 6P, 6Z, C2, M2 and G2 flashlights. It may or may not fit other models. The input voltage is 3.8 - 9 volts. Below 3.8 volts it will drop out of regulation and run direct drive. The output is 140+/- lumens. The current draw is approximately 350ma at 6 volts. The runtime is approximately 4 1/2 hours on 2 CR123 primary batteries. The LED is a Cree XRE 7090, Q5 bin, WG tint.

**These new models DO NOT have the clam shell packaging. They will be shipped in Bubble wrap**

$53.99

M60L (Low Output) to fit Surefire
This is the Malkoff Devices Low Ouput version of the P60 style dropin with solid brass heatsink construction. This design utilizes a Cree 8 degree optic. The optic has a very nice balance between throw and spill. It is an outstanding room lighter and short to medium spotter. It was designed specifically for use in SureFire 6P, 6Z, C2, M2 and G2 flashlights. It may or may not fit other models. The input voltage is 3.8 - 9 volts. Below 3.8 volts it will drop out of regulation and run direct drive. The output is 140+/- lumens. The current draw is approximately 350ma at 6 volts. The runtime is approximately 4 1/2 hours on 2 CR123 primary batteries. It will easily illuminate objects at 150+ feet. The LED is a Cree XRE 7090.

A fitting ring is required if used with a shock-absorbing head (ie M2).

WARNING: This light is capable of causing eye damage at close range. Please use the light responsibly!!!
Note: This drop-in module is intended to operate for extended periods in metal or plastic lights.

M60LL (lowest output) to fit Surefire
This is the Malkoff Devices Low Low Ouput version of the P60 style dropin with solid brass heatsink construction. This design utilizes a Cree 8 degree optic. The optic has a very nice balance between throw and spill. It is outstanding for close work and as an emergency/general purpose light. It was designed specifically for use in SureFire 6P, 6Z, C2, M2 and G2 flashlights. It may or may not fit other models. The input voltage is 3.8 - 9 volts. Below 3.8 volts it will drop out of regulation and run direct drive. The output is 80+/- bulb lumens. The current draw is approximately 170ma at 6 volts. The runtime is approximately 8 hours, at full output, on 2 CR123 primary batteries. It will easily illuminate objects at 100+ feet. The LED is a Cree XRE 7090. A fitting ring is required if used with a shock-absorbing head (ie M2).
WARNING: This light is capable of causing eye damage at close range. Please use the light responsibly!!!
Note: This drop-in module is intended to operate for extended periods in metal or plastic lights.

This is the Valiant Concepts - Malkoff Devices (VME) E Series Head. This head assembly will convert any SureFire E Series, Aleph series, or Scout Weapon Light to use a Malkoff Devices M series dropin lamp assembly. It is available in Type III Black HA only, and is fully O-Ringed and gasketed for weather tightness.

Visit Malkoff devices for other Malkoff products! Tell them Unique Titanium sent you.